DYNAMIC ENGINEERING Conduction Cooled ccPMCParallel-TTL

Publication date on this website: Tuesday, May 05, 2009
Company: Dynamic Engineering
Category: Press Releases : Boards

Summary:
Does your system require single ended TTL or CMOS level signals? How about medium speed Analog data capture [ADC 1-10 MHz]? The Conduction Cooled PMC compatible ccPMC-Parallel-TTL has build options to have up to 64 independent digital IO and up to 8 ADC channels. The high density makes efficient use of precious PMC slot resources.

Full Text:
Does your system require single ended TTL or CMOS level signals? How about medium speed Analog data capture [ADC 1-10 MHz]? The Conduction Cooled PMC compatible ccPMC-Parallel-TTL has build options to have up to 64 independent digital IO and up to 8 ADC channels.

The high density makes efficient use of precious PMC slot resources. The IO is available for system connection through the rear [Pn4] connector. The rear panel IO has a PIM and PIM Carrier available for rear panel wiring options. The HDEterm68 can be used as a breakout for the rear panel IO when the PMC carrier has a SCSI style connector for the rear IO. The HDEcabl68 provides a convenient cable. The pin definitions are consistent with the PMC Parallel IO and PMC Parallel TTL designs to enable users to migrate to the ccPMC Parallel TTL quickly and easily when a conduction cooled solution is required.
http://www.dyneng.com/ccpmc_parallel_ttl.html

Features of the ccPMC-Parallel-TTL card

PMC Compatibility: PMC compliant per IEEE 1386 spec. and compliant with the conduction cooled PMC spec.

PCI Compatibility: PCI compliant. Develop with a PCI to PMC adapter - PCI2PMC or PCIBPMC etc..

Parallel Interface: 64 independent TTL IO. Pull-ups can be referenced to 3.3V or 5V. Rear IO [Pn4] Unused ports isolated with resistors for zero bus stub. Matched IO within 1/1000 inch for on-board traces.

Analog Interface: 8 independent / sychnonized ADC. 12 bit 10 MHz capable ADC´s with opamp buffers and voltage dividers. FIFO support with DMA for each channel. Signal Processing on received data or straight packed data.

Pull-up Resistor: 470 standard, 1K, 4.7K available. Double pull-ups available on digital lines

Sink Current: 64+ mA per channel on digital lines

Cable interface: Pn4 backplane connection. Your PMC carrier will specify the system connector.

Software Interface: 32 bit registers mapped to the 64 IO channels. Read-back of channel control registers and input registers. Read-write of control registers for card configuration. Direct and DMA read of ADC data.

Interrupts: All IO Channels can be programmed to cause interrupts. Each channel is programmable to be masked, rising, falling, both [COS]. Level interrupts plus DMA completion on ADC channels. Interrupts are mapped to INTA on PCI bus.

Power Requirement: +3V, +5V, and +/- 12V when ADC´s are installed.

COS Clock: Input registers are programmable to capture data with the COS clk. SW can select PLL or Oscillator as the source for clock. A programmable divider allows a wide range of sampling frequencies to be selected.

Custom: All bits are routed through the FPGA to allow for custom state-machine implementations. FIFO and Dual Port RAM can be implemented. See custom models below.

Speed: ccPMC-Parallel-TTL is a software controlled HW interface. As fast as the PCI interface can push the data across, the outputs can change. With the Windows® driver several accesses per microsecond can be achieved. Your time to market will be shortened by the easy to use interface, flexibility in design, and off-the-shelf availability. With DMA enabled and FIFO´s instantiated faster transfers can occur. Up to 48K x 32 internal FIFO can be achieved with the 4000 sized FPGA.

Price: ccPMC-Parallel-TTL has an attractive price, and low integration cost for a low system cost. ccPMC-Parallel-TTL has an associated PIM and PIM Carrier which can lead to further savings in cPCI environments.

Ease of Use: ccPMC-Parallel-TTL is easy to use. A point and shoot user interface to the IO.

Availability: ccPMC-Parallel-TTL is designed to be customized. The base version is available from stock. "clientized" versions can be dialed in quickly, shipping a model that is just like but different to you instantaneously and follow-up with new FLASH files to match your requirements. You can make a quick start having the HW available right away and adding features as they are available

Contact:
Dynamic Engineering
www.dyneng.com
sales@dyneng.com
831 457 8891
http://www.dyneng.com/ccpmc_parallel_ttl.html